产品详情
十大网赌app排行榜
无励磁鼓(管)型分接开关
De-energized drum-form (tube-form) tap-changer
无励磁管型及鼓形分接开关(WDG系列、WDG+WLG系列、WSG系列)额定电压110kV(设备最高电压126kV)及以下,额定电流4000A及以下,有三相联动操作、1+2相操作、单相操作,其方式分箱盖箱底、箱壁侧面直接或联动操作。
De-energized tube-form and drum-form tap-changer(WDG,WDG+WLG,WSG series), the specification of the product is with rated voltage of 110kV(the highest voltage for equipment of 126kV)and below, rated current 4000A and below with three-phase parallel operation,1+2 phase or single phase operation. The ways of operation are directly or parallly operated on the cover,at the bottom or side of transformer.
最靠谱的网赌软件产品型号说明
De-energized tap-changer introduction of product model
※①TH:湿热带; TA:干热带;
②QMF:全密封(适用于盘形、条形开关) ;
③W:卧式,L:立式;
④Q:钟罩式安装;
⑤XH:带远方信号显示接点
⑥Y:中性点引出;
⑦X:带电外限小( 适用于大笼形开关)
⑧Z:支撑座采用金属材料(适用于条形开关)
⑨F:反向( 适用于条形开关)
⑩S:双密封(适用于盘形、条形开关)
1.由于产品型号规格较多,在选型时请准确书写型号,当型号还不能表达您的需求时,请您提出附加要求;
2.请在选型时注意,以上未完善参数或特殊参数以样本当页产品中为准;
①TH: Humidity tropical area TA: Exothermic area
②QMF: Airproof (used in linear switch and rotary switch )
③w: Horizontal L: Vertical
④Q: Bell cover installation
⑤XH: Display interface with remote signal
⑥Y: Draw forth for neutral point
⑦X: Electricity within certain limits(designed for large cage-formed )
⑧Z: Metal support (designed for bar-formed)
⑨F: Reverse(designed for bar-formed)
⑩S: Double airproof (designed for tray-formed and bar-formed )
1.Because we have manufactured many varieties of circuit tap-changers, customers are required to down the correct model of the tap-changer If the informnation about the tap-changer you desire in the catalogue is isuficient, Please attach your additional requirements on your order.
2.Customers should be aware while the brief introductions of the whole series of products are not explicit enough, We strongly recommend you to cheek the specifications on the page of the model you desire in the catalogue.
无励磁鼓(管)形(G)分接开关
De-energized pipe-type tap-changer
产品适用范围及特点
一种新三相管型开关,由开关本体和操作转动机构组成,在变压器无励磁状态下,通过对其进行分接位置转换,以改变变压器变比,达到稳定的电压输出。单相管型开关和“1+2”相管型开关适用立式安装,三相管型开关适用立式或卧式安装。
该系列产品适用于频率为50Hz或60Hz大中型油浸式电力变压器以及特种变压器,全密封变压器;适用于平顶式油箱和钟罩式油箱,其设备最高电压为252kV及以下,额定适应电流4000A及以下。
管形开关的特点颇丰,已取得多项国家专利加以保护
(1)管形外观,简洁明快;无可靠性差结构,无不坚固构件,可靠性一目了然;
(2)转动力矩轻盈,到位手感清晰。设计特色:二者互为制约,相辅相成,调节适宜。操作换档轻捷自如,准确无误,比同类产品明显优越;
(3)外部壳体取消繁杂的导体连接及外罩,制成封闭式具有抗高电压屏障的外绝缘,安装开关的夹空即便狭窄到使其贴近变压器器身,也不会放电击穿;
(4)还研制出管型开关内部结构一次性全部抽出的绝窍,极大地方便总装和维护。
The usage scope and technical features of tube-type tap-changer
This is an new three- phase tube-type tap-changer,it is combined by the body of tap-changer and an operating turning framework, when the transformer is under non-energized state , we can turn over the tap position to change transformer ratio and stabilize output voltage,The single phase and “ 1+2” phase tube-type tap-changer are suitable for installation on vertical direction,but the three-phase tube-type product is suitable for vertical or horizontal installation .
These series of products are specially designed for large or medium oil-immersed power transformer, full hermetically transformer or transformers for specially used , they are frequency normally on 50Hz or 60Hz, and suitable for flat type or bell-type oil tank , its Highest voltage for equipment is up to 252kV and below ,rated current up to 4000A and below.
This product has many technical features and owned a certain of national patent right protection .
(1) Simple and lively appearance ,reliable structure equipped with solid construct pieces .
(2) Light moment , turn over tap position clearly . The product has technical design features as following : body pieces are restricted each other and functioned each other ,you can change the tap position freely and exactly ,compared with the same type of products , it has obvious superiority features.
(3) No conductors and switch cover being equipped on the outer body of product . This is a full hermetially outer insulation screen which can withstand high voltage impulse .so no puncture discharge will rise between the narrow gaps , even if the air gap of the tap-changer is very near the active body of the transformer.
(4) The inner structure of the tube- type tap-changer can be drawn out as a whole part , this helps to installation and maintenance.
管型及其笼型开关主要技术性能指标
Pipe-Type and their cage-form tap-changer technical performance parameter
无励磁鼓(管)形分接开关配置及选型
The equipments and type select of de-energized drum (tube) tap-changer
产品基本配置 Equipments of the product
1.管形开关(径向出线)提供操动机构、绝缘操纵杆、焊接法兰盘及密封圈,鼓形开关(轴向出线)不提供焊接法兰盘;
2.管形开关配绝缘操纵杆长800mm,鼓形开关配绝缘操纵杆长1200mm,若需加长用户订货时提出;
3.鼓(管)形开关分接引线长度为700mm,特殊要求用户提出;
4.配用引线截面: 250A →70mm2; 400A→120mm2; 500A→1 50mm2 ; 630A→1 85mm2 ; 800A →240mm2 ;
1000A及以上为双引线,特殊要求用户提出;
5.引线表面绝缘处理方式:管(鼓)形开关引线绝缘包长500mm, 10 ~ 35kV单边包厚4mm,66 ~ 110kV单边包厚6mm,220kV单边包厚10mm。
1.Pipe-form switch (radial line) is equipped with operation mechanism, insulation controlling pole, welding flange and seal wash.Drum switch (axis line) is equipped without flange.
2.Pipe-form switch is equipped with an insulation controlling pole of 800mm, and drum switch with a 1200mm one. If you need a longer one, please indicate in the order.
3.The length of drum tap-changer (pipe-form tap-changer) lead is 700mm, user can specify with exceptive requirements.
4.The applicable lead section: 250A - > 70mm* ; 400A →120mm' ; 500A →150mm*; 630A→185mm'; 800A→240mm' ;1000A and up, use twin lead user can specify with exceptive requirements.
5.Insulation methods of lead section: insulation cover of drum switch lead is 500mm, one layer-thickness of the cover for 10 ~ 35kV transformer lead is 4mm, and 66 ~ 110kV 6mm,220kV 10mm. Drum switch is not covered.
鼓(管)形开关箱下侧操作及联动结构示意图1
Tank' s down-side operation and linkage configuration diagram
鼓(管)形开关箱下侧操作及联动结构示意图2
Tank' S down-side operation and linkage configuration diagram
落地手动操作结构示意图
The manual landing operation structure diagram
落地电动操作结构示意图
The electric landing operation structure diagram
WDG II 单相鼓形最靠谱的网赌软件
WDG II series de-energized drum-formed tap-changer
本开关由开关本体和操作机构组成,采用压缩弹簧、环形动触头,具有结构合理,操作简单,能自动定位,手感强,接触好等优点。适用于频率50Hz、60Hz,设备最高电压40.5kV、126kV、252 kV,额定电流200A~2500A的油浸式变压器,开关部份固定在器身或下部油箱箱沿.上,操作转动机构固定在箱盖上,在无励磁状态下分接调换。
This type of changer is comprised by tap-changer body and operating mechanism, Being adopted by crank principle ,compress spring and ring-type motive contact, They have the merits of reasonable in structure ,operating simply ,location automation,good in handing and contact reliable etc, It is suitable for oil-immersed transformer with frequency of 50 or 60Hz,highest voltage for equipment 40.5kV or 126kV and 252kV,rated current from 200 A to 2500A, The body of tap-changer is fixed on the tanking transformer or on the body of lower part of oil tank, The operating mechanism is located on the tank cover, they must be working under non-energized condition.
鼓形开关特点:
1、开关本体部分:
a、转动部位采用新结构,具有转动灵活,操作力矩小,使开关在干燥处理后(高温状态),也能正常操作;
b、增设了自动定位装置,动触头过“死点”后,能自动定位,消除了动触头偏位现象,具有操作手感强的特点;
C、增设了导向筒,使开关在二次装配时,操纵杆的插入准确,方便。
2、开关的操纵机构部分:
a、采用新的法兰压紧固定方式,机构的法兰可随开关本体档位角度任意转动,而不需调整档位指示角度;
b、只要把操纵杆按实际的长度进行有效的对接即可,使装配更为简化;
c、操作未到位时,手柄无法定位,使罩子无法戴.上,具有防止误操作功能。
New features of drum-formed tap-changer
1、The part of tap-changer body
a、The turning part of the tap-changer is made of new structure ,turning flexibly and small operating moment.It can work normally after the tap-changer is dried with high temperature.
b、The automatic orientation device is made in the switch,after the motive contact is passed through“ dead point', it can orientate by itself and eliminate the position excursion phenomena,This operation makes the tap-changer have strong handle feeling.
C、The direction guiding barrel is added in the switch,when the switch is assembled once again, the operating pole can be inset to the position exactly and conveniently.
2、The part of operating mechanism
a、The flange is fixed with new installation method, the flange on the operating mechanism can turn freely along with the turning angel of the tap-changer body. Adjustment the steps of tap-changer is not required.
b、Only connect rightly to the operating pole using its actual length, it makes assembly more easily.
C、When the tap-changer is turned to the end part of position, the handle pole can not be gone forward and the cover can' t be put on, this will prevent the tap-changer from any fault operation.
WDG ll₃ ( 126kV )单相鼓形分接开关( 250-2000A )
WDG II₃ series ( 126kV ) de-energized drum-formed tap-changer
WDG ll₂ ( 252kV )单相鼓形分接开关( 250-1600A )
WDG ll₂ Series de-energized drum-formed tap-changer
WDG ll₂ ( 252kV )单相鼓形分接开关( 250-1600A )
WDG ll₂ Series de-energized drum-formed tap-changer
三相立式线性调( |、|△)管形(G)分接开关(250~ 800A)
Three-phases linear voltage-regulating( |、1△ )pipe-form (g) vertical tap-changer
三相立式线性调( |、|△)管形(G)分接开关(1000~ 2000A)
Three-phases linear voltage- -regulating( |、|△)pipe-form (g) vertical tap-changer
1+2相立式线性调( |、| △)管形(G)分接开关(250~ 800A)
“1+2”phases linear voltage-regulating( |、| △)pipe-form (G) vertical tap-changer
1+2相立式线性调( |、|△)管形(G)分接开关(1000~2000A)
“1+2”Phases linear voltage-regulating( |、|△)pipe-form (g) vertical tap-changer
三相立式单桥跨接( II )管形(G)分接开关(250 ~ 800A)
Three-phases linkage single-bridge crossing connection( II )pipe-form (g) vertical tap-changer
三相立式单桥跨接( II )管形(G)分接开关(1000 ~ 2000A)
Three-phases linkage single-bridge crossing connection( II )pipe-form (g) vertical tap-changer
“1+2”相立式单桥跨接( II )管形(G)分接开关(250 ~ 800A)
“1+2”phase linkage single-bridge crossing connection( II )pipe-form (g) vertical tap-changer
“1+2”相立式单桥跨接( II )管形(G)分接开关(1000 ~ 2000A)
“1+2”phase linkage single-bridge crossing connection( II )pipe-form (G) vertical tap-changer
三相卧式(W)单桥跨接(II)管形(G)分接开关(250 ~ 800A)
Three-phases linkage single-bridge crossing connection( II ) pipe-form (G) horizontal tap-changer
三相立式Y -△转换(IV)管形(G)分接开关(250 ~ 1000A)
Three-phases vertical y -△ exchanger ( IV ) pipe (g) tap-changer
“1+2”相立式Y -△转换(IV)管形(G)分接开关(250 ~ 800A)
“1+2”Phases vertical y -△ exchanger ( IV ) pipe (g) tap-changer
三相立式双桥跨接( V )管形(G)分接开关(250 ~ 800A)
Three-phases double-bridge crossing connection( V )pipe-form vertical tap-changer
“1+2”相立式双桥跨接( V )管形(G)分接开关(250 ~ 800A)
“1+2”phase double-bridge crossing connection( V )pipe - form(G) vertical tap-changer
三相立式串-并联( VI)管形(G)分接开关(250 ~ 800A)
Three-phases series - parallel exchanger ( VI) pipe -form (G) vertical tap-changer
“1+2”相立式串-并联(VI)管形(G)分接开关(250 ~ 800A)
“1+2”Phase series -parallel exchanger (VI) pipe-form (g) vertical tap-changer
三相立式正反调(VII、VII△ )管形(G)分接开关(250 ~ 800A)
Three-phases positive-negative voltage-regulating (VII、VII△ ) pipe-form (g) vertical tap-changer
三相立式正反调(VI)管形(G)分接开关(1000 ~ 2000A)
Three-phases positive-negative voltage-regulating ( VIIl ) pipe-form (G) verical tap-changer
“1+2”相立式正反调(VI)管形(G)分接开关(250 ~ 800A)
“1+2”phase positive- negative voltage- regulating (VI) pipe-form (g) vertical tap-changer
“1+2”相立式正反调(VI)管形(G)分接开关(1000 ~ 2000A)
“1+2”phase positive- negative voltage - regulating (VI) pipe-form (G) verical tap-changer
地址:浙江省台州市三门县海润街道凤鸣路3号
产品销售热线:+86-576-83379018 / 83379188
技术咨询电话:+86-576-83379026
传真:+86-576-83379155
邮箱:tl@bangjielvxin.com
网址:bpl.bangjielvxin.com
访问手机二维码
腾龙
Copyright © 最靠谱的网赌软件 版权所有 浙ICP备13034569号 网站建设:中企动力台州